1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Error messages - ThinkPad General

Discussion in 'Casie Studies' started by Administrator, Jun 13, 2018.

  1. Administrator

    Administrator Administrator Staff Member

    Joined:
    Apr 6, 2017
    Messages:
    48,303
    Likes Received:
    87
    Error messages - ThinkPad General

    Symptom or error FRU or action, in sequence
    Device address conflict
    1. Load Setup Defaults in BIOS Setup Utility
    2. Backup battery
    3. System board
    Allocation error for device
    1. Load Setup Defaults in BIOS Setup Utility
    2. Backup battery
    3. System board
    Failing bits: nnnn
    1. DIMM
    2. System board
    Invalid system configuration data
    1. DIMM.
    2. System board.
    I/O device IRQ conflict
    1. Load Setup Defaults in BIOS Setup Utility
    2. Backup battery
    3. System board
    Operating system not found
    1. Check that operating system has no failure and is installed correctly
    2. Enter BIOS Setup Utility and see whether the hard drive and the diskette drive are properly identified
    3. Reseat the hard drive
    4. Check the boot sequence by use of BIOS Setup Utility
    5. Reinstall the operating system
    6. Diskette drive
    7. Hard drive
    8. System board
    Hibernation error
    1. Restore the system configuration to what it was the before the computer entered hibernation mode.
    2. If memory size has been changed, re-create the hibernation file.
    Fan error
    Fan

    Thermal sensing error
    System board

    Unsupported memory
    configuration
    Shut down the computer and remove the extra memory. Maximum memory size is:

    • 256 MB for A21e series and the low-end models of A22e
    • 512 MB for the high-end models of A22e
    Do you want abort resume from hibernation? (Y/N) System memory removed, press F3 to power off system and restore memory chip, press F4 to normal boot.
    1. Restore the system configuration to what it was before the computer entered hibernation mode
    2. If the memory size has been changed, re-create the hibernation file
    Docking station is removed or its ID is different, press F3 to power off system and restore correct docking station, press F4 to normal boot.
    No error appears when; undock, hibernation, dock, wakeup. The docking is configured by the Operating System.
    Authentication of system services failed. Press the Esc key to resume.
    The Predesktop Area in the hard drive is corrupted. To use the Predesktop Area, restore it from a recovery CD.

    CD ROM drive
    1. DIMM
    2. System board
    Entering SETUP
    1. DIMM
    2. System board
    Fixed disk n
    1. DIMM
    2. System board
    P/S 2 mouse boot summary screen
    1. DIMM
    2. System board
    One or more I2O block storage devices were excluded from the setup boot menu
    1. DIMM
    2. System board
    Parity Check 1 nnnn
    1. DIMM
    2. System board
    Parity Check 2 nnnn
    1. DIMM
    2. System board
    Press F1 to resume, F2 to Setup, F3 for previous
    1. DIMM
    2. System board
    Press F2 to enter Setup
    1. DIMM
    2. System board
    PS/2 Mouse
    1. DIMM
    2. System board
    Run the I2O Configuration Utility
    1. DIMM
    2. System board
    System BIOS shadowed
    1. DIMM
    2. System board
    UMB upper limit segment address: nnnn
    1. DIMM
    2. System board
    Video BIOS shadowed
    1. DIMM
    2. System board
    WRONG MEMORY: Serial Presence Detected (SPD) indicates 66MHz Memory. This processor requires 100MHz memory. Shut system down.
    Shut system down.(Stop at this point).

    Cannot boot from any device.
    Check the status of device which you want to boot from.

    Device not found.

    1. The device you want to boot from.
    2. System board.
    Device Error.

    1. The device you want to boot from.
    2. System board.
    No valid operating system.

    1. Check that the operating system has no failure and is installed correctly.
    2. Reinstall the operation system.
    Excluded from boot order.

    • Enter the BIOS Setup Utility and add the device in boot order.
     

Share This Page